RTR
VXM
Anaheim
RTR Controller
DCNC-RTR-ClassicThis is a Ready to Run set for the smaller applications. This fully assembled and tested controller works perfectly with 2NM or 2,5NM stepper motors, even up to 4NM steppers. It is also used to retrofit mills and lathes.
Set is fully assembled and tested
Powder Coated Housing
4 HP5056 drivers
Cooling Fan
Technical Support via Email or Skype
48V-12V DC power supply
Includes required mains + USB cable
USBCNC Config file and startup manual
Plug and play Inductive/LimitSwitch Connection
Emergency Stop (Wired and tested)
2x220V Output, to turn on/off spindle and coolant
Probe input connection
Prepared for MPG hand wheel
USBCNC CPU V4.0 Controller Integrated
RTR Specifications
Category
RTR Specifications
Interface
USB 2.0
Power
110V
Number of Axis
Up to 5
VXM Controller
The VXM is a high performance, programmable, 2 phase, unipolar stepper motor controller. It features:
Small size (3.5" x 4.4" x 6.6") and low cost. Controls 1 to 4 motors.
Powerful 115 intuitive command Instruction Set makes it easy to program
4X oversize motor drives for long life and overload tolerance
Complete Controller/Indexer/Driver/AC Power Supply with RS-232 interface
Nonvolatile memory for storing 4 user-created programs
Easy-to-use graphical user interface. More about COSMOS software
24 Volt CE certified power supply
VXM Specifications
Category
VXM-1 Specifications
Type
Programmable control and driver
Number of axes
1 to 4 (with additional controllers linked together)
Simultaneous Motors
Yes
Motor Compatibility
Nema size 17 - 34 (1.2 to 4.7 amp)
Step / Revolution
400
Program Storage (memory type)
5 (RAM / FLASH)
Interface
RS-232
Aux. Inputs / Outputs
4 in / 2 out
Speed Range (steps / sec)
1 to 6000
Default Baud Rate
9600
Maximum Baud Rate
38,400
Program Language
ASCII Characters
Stand Alone Operation
Yes
Manual Jog
Yes
Anaheim Controller
The PCL601XCE Programmable Controller provides you with a complete motion solution in a compact package. It simplifies programming tasks and provides the essential features for any positioning system. The PCL601XCE features the ability to connect to a PC and instantly provide movement for a stepper motor. The PCL601XCE's programming capabilities allows you to develop motion routines, turn on discrete outputs, monitor inputs, and much more. The controller contains 2KB of nonvolatile stored programming space and encoder feedback. It achieves communication from a PC or any RS232/RS485 machine controller serial port.
Cost Effective motion Control Solution
Easy to Use Windows Software Included
Stored Program Capabilities
24V Compatible Inputs
0-5V Analog Input for Speed or Distance
Encoder Feedback
Multi-Drop Capabilities
Compact and Rugged Construction
CE Certified and RoHS Compliant
Anaheim Specifications
Category
Specifications
Power Requirements
8 - 24 VDC, 50/60Hz (0.5W Peak Power)
Nonvolatile Memory
2KB of stored programming space
Baud Rate
38,400 Baud, Fixed
Data Format
Half Duples, 1 start bit, 8 data bits, no parity, 1 stop bit
Communication Protocol
RS232 or RS485 selectable
Encoder Feedback
Quadrature, CHA, CHB, 5VDC Signal Compatibility
Controller Outputs
8 Programmable Outputs, Open Drain Type, 40V, 100mA, +5VDC Output, 50mA
Controller Inputs
6 Programmable Inputs
Logic 0: 0 - 0.8VDC
Logic 1: 3.5 - 24VDC
Analog Input: 0 - 5VDC
Pulse Output Range
1 - 50KHz, 10 micro seconds negative going pulse width
© 2014 All Rights Reserved M3DI